98 lines
3.1 KiB
C++
98 lines
3.1 KiB
C++
/**
|
|
* The MySensors Arduino library handles the wireless radio link and protocol
|
|
* between your home built sensors/actuators and HA controller of choice.
|
|
* The sensors forms a self healing radio network with optional repeaters. Each
|
|
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
|
|
* network topology allowing messages to be routed to nodes.
|
|
*
|
|
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
|
|
* Copyright (C) 2013-2015 Sensnology AB
|
|
* Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
|
|
*
|
|
* Documentation: http://www.mysensors.org
|
|
* Support Forum: http://forum.mysensors.org
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* version 2 as published by the Free Software Foundation.
|
|
*
|
|
*******************************
|
|
*
|
|
* DESCRIPTION
|
|
* The ArduinoGateway prints data received from sensors on the serial link.
|
|
* The gateway accepts input on seral which will be sent out on radio network.
|
|
*
|
|
* The GW code is designed for Arduino Nano 328p / 16MHz
|
|
*
|
|
* Wire connections (OPTIONAL):
|
|
* - Inclusion button should be connected between digital pin 3 and GND
|
|
* - RX/TX/ERR leds need to be connected between +5V (anode) and digital pin 6/5/4 with resistor 270-330R in a series
|
|
*
|
|
* LEDs (OPTIONAL):
|
|
* - To use the feature, uncomment MY_LEDS_BLINKING_FEATURE in MyConfig.h
|
|
* - RX (green) - blink fast on radio message recieved. In inclusion mode will blink fast only on presentation recieved
|
|
* - TX (yellow) - blink fast on radio message transmitted. In inclusion mode will blink slowly
|
|
* - ERR (red) - fast blink on error during transmission error or recieve crc error
|
|
*
|
|
*/
|
|
|
|
// Enable debug prints to serial monitor
|
|
#define MY_DEBUG
|
|
|
|
|
|
// Enable and select radio type attached
|
|
#define MY_RADIO_NRF24
|
|
//#define MY_RADIO_RFM69
|
|
|
|
// Set LOW transmit power level as default, if you have an amplified NRF-module and
|
|
// power your radio separately with a good regulator you can turn up PA level.
|
|
#define MY_RF24_PA_LEVEL RF24_PA_LOW
|
|
|
|
// Enable serial gateway
|
|
#define MY_GATEWAY_SERIAL
|
|
|
|
// Flash leds on rx/tx/err
|
|
#define MY_LEDS_BLINKING_FEATURE
|
|
// Set blinking period
|
|
#define MY_DEFAULT_LED_BLINK_PERIOD 300
|
|
|
|
// Inverses the behavior of leds
|
|
//#define MY_WITH_LEDS_BLINKING_INVERSE
|
|
|
|
// Enable inclusion mode
|
|
#define MY_INCLUSION_MODE_FEATURE
|
|
// Enable Inclusion mode button on gateway
|
|
#define MY_INCLUSION_BUTTON_FEATURE
|
|
|
|
// Inverses behavior of inclusion button (if using external pullup)
|
|
//#define MY_INCLUSION_BUTTON_EXTERNAL_PULLUP
|
|
|
|
// Set inclusion mode duration (in seconds)
|
|
#define MY_INCLUSION_MODE_DURATION 60
|
|
// Digital pin used for inclusion mode button
|
|
#define MY_INCLUSION_MODE_BUTTON_PIN 3
|
|
|
|
#define MY_DEFAULT_ERR_LED_PIN 4 // Error led pin
|
|
#define MY_DEFAULT_RX_LED_PIN 6 // Receive led pin
|
|
#define MY_DEFAULT_TX_LED_PIN 5 // the PCB, on board LED
|
|
|
|
#include <SPI.h>
|
|
#include <MySensor.h>
|
|
|
|
void setup() {
|
|
// Setup locally attached sensors
|
|
}
|
|
|
|
void presentation() {
|
|
// Present locally attached sensors
|
|
}
|
|
|
|
void loop() {
|
|
// Send locally attached sensor data here
|
|
}
|
|
|
|
|
|
|
|
|
|
|