/**
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2015 Sensnology AB
 * Full contributor list: https://github.com/mysensors/Arduino/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 * REVISION HISTORY
 * Version 1.0 - Henrik Ekblad
 * Contribution by: Derek Macias
 * 
 * DESCRIPTION
 * Example showing how to create an atuator for a servo.
 * Connect red to +5V, Black or brown to GND and the last cable to Digital pin 3.
 * The servo consumes much power and should probably have its own powersource.'
 * The arduino might spontanally restart if too much power is used (happend
 * to me when servo tried to pass the extreme positions = full load).
 * http://www.mysensors.org/build/servo
 */

// Enable debug prints to serial monitor
#define MY_DEBUG 

// Enable and select radio type attached
#define MY_RADIO_NRF24
//#define MY_RADIO_RFM69

#include <SPI.h>
#include <MySensors.h>
#include <Servo.h> 

#define SERVO_DIGITAL_OUT_PIN 3
#define SERVO_MIN 0 // Fine tune your servos min. 0-180
#define SERVO_MAX 180  // Fine tune your servos max. 0-180
#define DETACH_DELAY 900 // Tune this to let your movement finish before detaching the servo
#define CHILD_ID 10   // Id of the sensor child

MyMessage msg(CHILD_ID, V_DIMMER);
Servo myservo;  // create servo object to control a servo 
                // a maximum of eight servo objects can be created Sensor gw(9,10);
unsigned long timeOfLastChange = 0;
bool attachedServo = false;
            
void setup() 
{ 
  // Request last servo state at startup
  request(CHILD_ID, V_DIMMER);
} 

void presentation()  {
  // Send the sketch version information to the gateway and Controller
  sendSketchInfo("Servo", "1.0");

  // Register all sensors to gw (they will be created as child devices)
  present(CHILD_ID, S_COVER);
}

void loop() 
{ 
  if (attachedServo && millis() - timeOfLastChange > DETACH_DELAY) {
     myservo.detach();
     attachedServo = false;
  }
} 

void receive(const MyMessage &message) {
  myservo.attach(SERVO_DIGITAL_OUT_PIN);   
  attachedServo = true;
  if (message.type==V_DIMMER) { // This could be M_ACK_VARIABLE or M_SET_VARIABLE
     int val = message.getInt();
     myservo.write(SERVO_MAX + (SERVO_MIN-SERVO_MAX)/100 * val); // sets the servo position 0-180
     // Write some debug info
     Serial.print("Servo changed. new state: ");
     Serial.println(val);
   } else if (message.type==V_UP) {
     Serial.println("Servo UP command");
     myservo.write(SERVO_MIN);
     send(msg.set(100));
   } else if (message.type==V_DOWN) {
     Serial.println("Servo DOWN command");
     myservo.write(SERVO_MAX); 
     send(msg.set(0));
   } else if (message.type==V_STOP) {
     Serial.println("Servo STOP command");
     myservo.detach();
     attachedServo = false;

   }
   timeOfLastChange = millis();
}